100m Wireless Sensor for Burglar Alarm Main Unit

Roller shutters or rolling doors have many applications, including applications for vans, garages, kitchens, schools and warehouse. The door is raised to open it and lowered to close it. Both roller shutter and rolling doors provide protection against wind and rain.
Roller Shutterrolling-doors
Now we recommend this kind of rf wireless magnetic sensor (W-13) to install to roller shutters or rolling doors to protect windows or gates from vandalism and burglary attempts. It will send signal to alarm main unit to alert people once it is triggered.
sensor-kit
This kit contains a sensor, a magnetic bar, a transmitter and 4 screws. It works with 100m in the open field. Alarm time of this kit is 5 seconds. With indication of low battery, you can change battery in time.
 magnetic-bar&sensor-(2)sensor
transmitter
Installation:
Stick part A (magnetic bar) on the edge of the roller shutter/rolling door, and stick part B on the fixed frame of roller shutter/rolling door
Note: The distance of these two parts shall be less than 3-5 cm when the roller shutter/rolling door is closed.
Usages:
Pull out the antenna of the transmitter.
When the roller shutter/rolling door is opened from the closed position, LED 1 will turn on red light for 5 seconds; the magnetic detector will be triggered and will send alarming signal to the main unit.
Indication of low battery: When the voltage of battery is less than 7.5V, LED 2 will straightly turn on red light. At this time, you must immediately change the battery.

Online shop: http://www.carymart.com/

Comments

Post a Comment

Popular posts from this blog

Short Description of Toggle / Momentary / Latched Working Modes

Generally there are three working modes for rf remote controls: toggle, momentary, latched. Toggle mode is used most often. Controlling lamp, for example, press the button of remote, turn on the lamp; press the button again, turn off the lamp. Momentary mode can be set to control rolling blind or rolling door. Press and hold the button of remote, open the blind or door; release the button, close the blind or door. Both toggle and momentary mode are motivated by single relay, which means you can work these two modes with single button remote. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time, e.g. press remote button A, relay A will be on, and relay B will be off; press remote button B, relay B will be on, and relay A will be off. To be more specific, when you control the lamp by latched mode, you should prepare at least two buttons remote. Press button A, the lamp is on; press button B, the lamp is off. Online s
Read more

Remote Control Electromagnetic Lock

Image
Electromagnetic lock is a locking device that consists of an electromagnet and an armature plate. The principle behind an electromagnetic lock is the use of electromagnetism to lock a door when energized. Essentially it consists of an electromagnet attracting a conductor with a force large enough to prevent the door from being opened. That is to say, if only we could cut off power supply and make electromagnet force between electromagnet and armature plate to disappear, the door would be opened. Furthermore, we just try to use a direct dc output momentary remote and one button transmitter to cut off electric power to open the door. The following demonstration will show. At first, we prepare material. The wiring When we supply power to electromagnetic lock, electromagnet will attract armature plate through magnetic force. The door is locked. When we press button, the power supply will be cut off. The door is open as soon as electromagnetic lock unlock instantly. What’s more, t
Read more

How to Make Motor Rotate in Positive and Reverse Direction by High Power Remote Control

Image
We are going to demonstrate that our 30 A high power remote controller controls high power motor to rotate in positive and reverse direction. This kind of controller is activated by dc 12v power supply with 30 A current output of each relay. It is very favorable for high power device. It also has four working modes including toggle mode, momentary mode, latched mode as well as momentary + toggle mode. First of all, let’s see material preparation. 1 x 2 channel dc high power remote control receiver (S2PU-DC12) 1 x 2-button remote transmitter (C-2) 2 x dc12v power adapters Some lines Secondly, see the wiring diagram below, B is normally open terminal; C is normally closed terminal and A is common terminal. Connect terminal C to the positive and connect terminal B to the negative. Terminal A is supposed to be connected to the motor. Note: The Power supply of receiver and motor must be provided individually in order to avoid interference between them. Switch on the power O
Read more