Remote Control Lawn Mowers

Question from customer:
“I received the item— 2 channel motor controller( S2PF-DC12+1CV-6-2) and installed it yesterday on my remote control lawn mower that I have made. Per the instructions for momentary control, I can get 1 motor to work at a time, either motor but only one and only in forward. I then changed, per your instructions for latch and each motor will go forward if started with remote, #1 and then #2 both will run forward only, but they cannot be controlled to go in the direction that I choose. Neither motor will reverse in any mode. I have to be able to control each motor independent of each other so I can drive the mower right and left to go the direction I want. Please advise!”
lawn-mower
Answer:
You chose the 2 channel motor controller. Although the controller has two relays for two motor, two relays will work in the same mode. That is to say, your two motors only work in momentary mode or latched mode for one time. We recommend two sets of 1 channel dc motor controllers (S1PF-DC12+1CV-4-2), which is only 30amps output and 500m/1500ft transmission distance. It controls DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V / 24V. There are two transmission frequencies, 315Mhz /433Mhz for this controller. You can install one controller set in 315Mhz to one motor, and install another controller set in 433Mhz to another motor, so that you can control each motor independent of each other. Each motor can be controlled by its only transmitter. It won’t generate any interference each other.
1_01_1
Usage:
Connect power supply DC12V / 24V to terminal “INPUT”; connect motor to terminal “OUTPUT”.
1_06
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button ▲: motor rotates in positive direction
Press button ■: motor stops
Press button ▼: motor rotates in reversal direction
Press button ■: motor stops
Setting control mode Momentary: Only connect Jumper-1 (CN1)
Press and hold button ▲: motor rotates in positive direction
Release button: motor stops
Press and hold button ▼: motor rotates in reversal direction
Release button: motor stops
Each receiver has two controlling modes, so you can set receiver 1 for latched mode and receiver 2 for momentary or set receiver 1 for momentary mode and receiver 2 for latched mode.

Online shop: http://www.carymart.com/

Comments

Post a Comment

Popular posts from this blog

Short Description of Toggle / Momentary / Latched Working Modes

Generally there are three working modes for rf remote controls: toggle, momentary, latched. Toggle mode is used most often. Controlling lamp, for example, press the button of remote, turn on the lamp; press the button again, turn off the lamp. Momentary mode can be set to control rolling blind or rolling door. Press and hold the button of remote, open the blind or door; release the button, close the blind or door. Both toggle and momentary mode are motivated by single relay, which means you can work these two modes with single button remote. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time, e.g. press remote button A, relay A will be on, and relay B will be off; press remote button B, relay B will be on, and relay A will be off. To be more specific, when you control the lamp by latched mode, you should prepare at least two buttons remote. Press button A, the lamp is on; press button B, the lamp is off. Online s...
Read more

Remote Control Electromagnetic Lock

Image
Electromagnetic lock is a locking device that consists of an electromagnet and an armature plate. The principle behind an electromagnetic lock is the use of electromagnetism to lock a door when energized. Essentially it consists of an electromagnet attracting a conductor with a force large enough to prevent the door from being opened. That is to say, if only we could cut off power supply and make electromagnet force between electromagnet and armature plate to disappear, the door would be opened. Furthermore, we just try to use a direct dc output momentary remote and one button transmitter to cut off electric power to open the door. The following demonstration will show. At first, we prepare material. The wiring When we supply power to electromagnetic lock, electromagnet will attract armature plate through magnetic force. The door is locked. When we press button, the power supply will be cut off. The door is open as soon as electromagnetic lock unlock instantly. What’s more, t...
Read more

AC Lamp is Controlled by Customized Delay Time RF Remote Controller

Image
We recommend 1channel 110V~220V customized delay time controller (S1RD-AC220+C-2). At first, it must be set delay time in advance. According to your own actual requirement, you can set delay time you want. e. g. delay time: 20 seconds. You cannot change delay time once it is set. It is applied for controlling lights, motors, fans, electrically operated door/ lock/windows/ blinds/ cars or other appliances with AC 110~240V or DC 0~28V. You can turn on/off device on the receiver with transmitter from any place within reliable distance (theoretical distance 100m), the wireless RF signal can pass through wall, floors, doors and other obstacles. Wiring: Initial state: B, C = Normally Open; A, B = Normally Closed. AC lamp is wired to normally open terminals B&C. And add additional ac power to AC lamp. The delay time is set in advance. It is non-adjustable.   Press button 1: Turn on the relay (connect B and C, disconnect A and B) After ...
Read more