Remote control lights for the track

Use wireless remote control kits to wireless remote control lights for the track in a long distance.

Here is the detail information:

One of our customer need to set up "warning" lights for the track and he ideally this would be done with wireless switching. He said that “Your RF DC transmitters and receivers of the long distance type are what we're looking for to remote control lights. I need to send you a diagram to explain what we need as wording this is difficult.”

The signal needs to travel at least 500 meters so the 2000m setup would be best. The receivers will trigger emergency flashing beacons.
    The layout is for motorcycle oval track competition and the transmitters and receivers need to be operated by officials to ensure the safety of all competitors. This is done by operating warning revolving beacons. For this reason the customer need our best operating combinations over a distance of probably 800 to 1000 meters with direct line of sight available to remote control lights....so he gather the 2000m Long Distance combination (with separate antenna) would be the best option.
    12 volt equipment is being used for all emergency lighting via a 12 Volt DC power source.
MP1,MP2,MP3 and MP4 are corner marshalling points and the transmitters only need the ability to switch the corresponding relay for that corner (MP1 to L1, MP2 to L2, MP3 to L3 and MP4 to L4 yellow on diagram).There needs to be no interference between each of these MP points so they can be operated independently of each other. Therefore each MP transmitter only needs to be one (1) channel.
    CC1-Is the main central control for the marshalling and is operated by the steward of the event. The Steward will be mobile so this transmitter will not be at any fixed point. To enable the Steward to have total control and over-ride the operations of officials at all MP points this transmitter will need to be of 6 Channel operation, one channel for each MP (yellow) point (channels 1 to 4) and one channel (number 5) to operate simultaneously all RED receivers on points L1, L2, L3 and L4. This is to enable the stoppage of a race at any time by switching to a "STOP" light at all these points. Button number 6 can be spare.
    SG1 - Is for the operation of the starting mechanism for each race (which could be up to 100) during the event.
    This transmitter needs to be 2 Channel to enable the switching of 2 GREEN (GL1 and GL2)lights at the starting area from Channel 1 and Channel 2 will activate 2 solenoids (SR1 and SR2). Therefore transmitter needs to be 2 channel and SR1, SR2, GL1 and GL2 receivers all each need to be 1 channel. GL1 and GL2 have to operate simultaneously from Channel 1 and SR1 and SR2 have to work simultaneously from Channel 2.

According to all the information he has mentioned above, we recommend him a series of long distance wireless remotecontrol kits to remote control lights. The theoretical working distance of the wireless remote control kits can reach about 5000m.

These remote control kits have feedback function and two ways working mode.

With the feedback function, they can let the user know whether he/she had already connected the transmitter and receiver successfully in such a long distance.

Here is the principle of the feedback function.

[Transmitter]   <---------

     |                         \

[Encode]                       \

     |                            |

[Channel]                [Feedback]   

     |                            |   

[Decode]                       /

     |                          /

[Receiver]     ---------->   

Two ways working mode: When the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter. When the transmitter receive the feedback signal of the receiver, the transmitter will exude a buzzing sound like “D~” which means it receive the feedback signal successfully.

The receiver is waterproof case with waterproof connectors. The receiver can be installed outdoors. They are also high power remote control kits, each relay output can work at maximum current 30A.

External magnetic sucker antenna with 5meters cable, the antenna can be installed outside the building to get better working distance

The remote control kits can be used to remote control lights, agriculture automation, industry automation, and home automation. It can control products on land, water and air, especially in a long distance, such as business signs, motorboat, farm, pasture, offshore unmanned operation, field call, remote security alarm, unmanned aerial vehicle, etc.