1 Channel Long Distance Remote Control for Air Compressor


Someone is interested in controlling an air compressor remotely. The air compressor is 12v dc and 20 amps.He wants this to be a long range remote control system with the ability to accommodate a heavy duty compressor. He only wants the remote control to have the “on” and “off” functions for this air compressor.

As we know, air compressor is a device that converts power (usually from an electric motor, a diesel engine or a gasoline engine) into kinetic energy by compressing and pressurizing air, which can be released in quick bursts. It is used for sanders, sprayers, nail guns or almost any other types of air tools. Definitely, remote controlling of air compressor is really an easy task, you can switch it on and off from a reliable distance. So we recommend this 1 channel 30A long range remote control (S1PU-DC12-ANT2+1CB-2) to you.
remote control air compressor
Maximum current of channel is 30amp which is very favorable for your air compressor. With external extend antenna, the transmitter and receiver have longer working range, up to 2000M.
antennaAntenna wire
The remote control operates in toggle, momentary and latched mode (set the mode as you like freely). We suggest setting latched mode because the receiver pairs with 2-button transmitter. One button controls “On”, another button controls “Off”.
Wire air compressor to the receiver as the following picture shown. This receiver is designed with normally open and close configuration. A&B terminals are normally open; A&C terminals are normally closed. Usually we connect device to normally open terminals. Air compressor can be connected to common terminal “A”.
circuit

Operation:
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press big button: Turn on the relay, turn on the air compressor.
Press small button: Turn off the relay, turn off the air compressor.

Online shop: http://www.carymart.com/

Comments

Post a Comment

Popular posts from this blog

Short Description of Toggle / Momentary / Latched Working Modes

Generally there are three working modes for rf remote controls: toggle, momentary, latched. Toggle mode is used most often. Controlling lamp, for example, press the button of remote, turn on the lamp; press the button again, turn off the lamp. Momentary mode can be set to control rolling blind or rolling door. Press and hold the button of remote, open the blind or door; release the button, close the blind or door. Both toggle and momentary mode are motivated by single relay, which means you can work these two modes with single button remote. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time, e.g. press remote button A, relay A will be on, and relay B will be off; press remote button B, relay B will be on, and relay A will be off. To be more specific, when you control the lamp by latched mode, you should prepare at least two buttons remote. Press button A, the lamp is on; press button B, the lamp is off. Online s...
Read more

Remote Control Electromagnetic Lock

Image
Electromagnetic lock is a locking device that consists of an electromagnet and an armature plate. The principle behind an electromagnetic lock is the use of electromagnetism to lock a door when energized. Essentially it consists of an electromagnet attracting a conductor with a force large enough to prevent the door from being opened. That is to say, if only we could cut off power supply and make electromagnet force between electromagnet and armature plate to disappear, the door would be opened. Furthermore, we just try to use a direct dc output momentary remote and one button transmitter to cut off electric power to open the door. The following demonstration will show. At first, we prepare material. The wiring When we supply power to electromagnetic lock, electromagnet will attract armature plate through magnetic force. The door is locked. When we press button, the power supply will be cut off. The door is open as soon as electromagnetic lock unlock instantly. What’s more, t...
Read more

AC Lamp is Controlled by Customized Delay Time RF Remote Controller

Image
We recommend 1channel 110V~220V customized delay time controller (S1RD-AC220+C-2). At first, it must be set delay time in advance. According to your own actual requirement, you can set delay time you want. e. g. delay time: 20 seconds. You cannot change delay time once it is set. It is applied for controlling lights, motors, fans, electrically operated door/ lock/windows/ blinds/ cars or other appliances with AC 110~240V or DC 0~28V. You can turn on/off device on the receiver with transmitter from any place within reliable distance (theoretical distance 100m), the wireless RF signal can pass through wall, floors, doors and other obstacles. Wiring: Initial state: B, C = Normally Open; A, B = Normally Closed. AC lamp is wired to normally open terminals B&C. And add additional ac power to AC lamp. The delay time is set in advance. It is non-adjustable.   Press button 1: Turn on the relay (connect B and C, disconnect A and B) After ...
Read more