Shut Manual Switch on and off to Remote Control LED Lamp

Question from customer:
I want a remote controlling unit that the transmitter is to function as a switch to the receiver activated by supplying a 12V DC current to the transmitter (switch it on). The receiver then permits a 12V DC current to be supplied to a designated appliance. When the transmitter is shut off the receiver will shut down.
T R 12V DC #3
Answer:
Maybe this kind of controlling unit —12V power Input RF remote control system (S1XL-DC12-ANT2+CB-2V) is suitable for you. It is applied for device controlling another device. The characteristic of the transmitter CB-2V will be triggered by DC power 5~28V input. We add external extended antenna which makes transmitting distance up to 2000m.
1_01
According to the picture above, he wants the transmitter can be activated by manual switch and turn receiver on/off when the current in that circuit is on/off. First, the transmitter is supposed to be connected to power supply and that manual switch. Second, designated appliance should be connected to receiver.
S1XL-DC12circuit
We prepare a demonstration for this practical use.
CB-2V-and manual switch
We switch on the manual switch and the transmitter will send an “ON” signal to the receiver. The receiver receives the signal to instruct the light to turn on. We switch off the manual switch and the transmitter will send an “OFF” signal to the receiver. The receiver receives the signal to instruct the light to turn off.
S1X-DC+CB-2V-lamp on

Online shop: http://www.carymart.com/

Comments

Post a Comment

Popular posts from this blog

Short Description of Toggle / Momentary / Latched Working Modes

Generally there are three working modes for rf remote controls: toggle, momentary, latched. Toggle mode is used most often. Controlling lamp, for example, press the button of remote, turn on the lamp; press the button again, turn off the lamp. Momentary mode can be set to control rolling blind or rolling door. Press and hold the button of remote, open the blind or door; release the button, close the blind or door. Both toggle and momentary mode are motivated by single relay, which means you can work these two modes with single button remote. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time, e.g. press remote button A, relay A will be on, and relay B will be off; press remote button B, relay B will be on, and relay A will be off. To be more specific, when you control the lamp by latched mode, you should prepare at least two buttons remote. Press button A, the lamp is on; press button B, the lamp is off. Online s...
Read more

Remote Control Electromagnetic Lock

Image
Electromagnetic lock is a locking device that consists of an electromagnet and an armature plate. The principle behind an electromagnetic lock is the use of electromagnetism to lock a door when energized. Essentially it consists of an electromagnet attracting a conductor with a force large enough to prevent the door from being opened. That is to say, if only we could cut off power supply and make electromagnet force between electromagnet and armature plate to disappear, the door would be opened. Furthermore, we just try to use a direct dc output momentary remote and one button transmitter to cut off electric power to open the door. The following demonstration will show. At first, we prepare material. The wiring When we supply power to electromagnetic lock, electromagnet will attract armature plate through magnetic force. The door is locked. When we press button, the power supply will be cut off. The door is open as soon as electromagnetic lock unlock instantly. What’s more, t...
Read more

AC Lamp is Controlled by Customized Delay Time RF Remote Controller

Image
We recommend 1channel 110V~220V customized delay time controller (S1RD-AC220+C-2). At first, it must be set delay time in advance. According to your own actual requirement, you can set delay time you want. e. g. delay time: 20 seconds. You cannot change delay time once it is set. It is applied for controlling lights, motors, fans, electrically operated door/ lock/windows/ blinds/ cars or other appliances with AC 110~240V or DC 0~28V. You can turn on/off device on the receiver with transmitter from any place within reliable distance (theoretical distance 100m), the wireless RF signal can pass through wall, floors, doors and other obstacles. Wiring: Initial state: B, C = Normally Open; A, B = Normally Closed. AC lamp is wired to normally open terminals B&C. And add additional ac power to AC lamp. The delay time is set in advance. It is non-adjustable.   Press button 1: Turn on the relay (connect B and C, disconnect A and B) After ...
Read more